Email:[email protected]

bridgeport j head spindle bearings uses

Just fill in the form below, click submit, you will get the price list, and we will contact you within one working day. Please also feel free to contact us via email or phone. (* is required).

  • Bridgeport J head bearings and lubrication - The

    2008-1-5 · The Bridgeport J-Head needs a matched set of ABEC-7 7207 angular contact bearings, which run around 200 - 300 for the set, depending on where you get them. Andy: the 6206 radial at the back-end of the spindle, and the 5207 dual-row angular contact bearing in the pulley stack are not precision bearings, so they should run ~20 - 40 at your ...

    Get Price
  • J-Head Spindle Bearings????? - Practical Machinist

    2009-1-31 · The step pulley bearings are 207 series and the bull gear hub bearings are 208 series. BUT, the other prefixes and suffixes determine the internal clearance, preload, etc. The step pulley bearings, for instance, may be low internal clearance (as my 1966 J head were) or may be preloaded.

    Get Price
  • Bridgeport J Head Spindle Bearings & Re Build...? | The ...

    2015-6-5 · I recently worked with a shops J head BP mill, older, maybe circa 1970's. I had trouble with milling and hole accuracy. I know something is bad with the spindle. Just sensing that it is not running true or to spec, TIR. I did not check with DTI but just looking at surface finish and hole...

    Get Price
  • J HEAD ASSEMBLY - bridgeportuk.com

    Home > BRIDGEPORT MANUAL MILL SPARE PARTS > J HEAD ASSEMBLY. J HEAD ASSEMBLY. 69 products. Sort by: ... ITEM 43 - 1276 Spindle Bull Gear Assembly (J95 J74 J96) £1,663.75. Add to Cart. ITEM 44 - 1277 1.5HP & 2HP Upper Bearing Step Pulley Shaft (J301) £25.03.

    Get Price
  • Bridgeport Step Pulley J Head Upper Gearbox and

    2015-6-27 · Bridgeport Step Pulley J Head Upper Gearbox and Upper Spindle Bearing Questions I am hoping that the professional machinists on this forum will take the time to help with my questions. I am into the J head on my mill and found that the upper gear box seemed to have been packed with grease and that the two bull gear spindle bearings (6203 ...

    Get Price
  • Bridgeport Rebuild Kits - H&W Machine Repair &

    Replacing the Spindle Bearings on a Bridgeport Head This kit containes everything you will need to complete a standard top half rebuild on your Bridgeport Series I 'J' Head (Step Pulley). The kit includes the following new parts: Drive Belt(1), Timing Belt (1), Top Half Bearings (6) & a tube of grease for the bull gear area of the head.

    Get Price
  • Bridgeport J head step pulley disassembly and

    2005-12-2 · I ordered new bearings, but I found the actual problem was the main nut that held all the bearings onto the spindle had come a little loose. Actually, it seemed like the long spacer tube had been given too large a champher, and the end of the tube had deformed slightly, allowing everything to …

    Get Price
  • BRIDGEPORT SPINDLE BEARINGS - The Home Shop

    2005-3-20 · head (MT2 spindle) as a conversion. One machine was a clausing vertical mill with the bridgeport head. Another was adding the bridgport head to a horizontal mill to make a combo vertical/horizontal machine. I already have a rockwell combo machine which uses a R8 spindle. I'm wondering how the rockwell vertical head compares to the bridgeport head?

    Get Price
  • Is this a Bridgeport J head - Home - Practical Machinist

    2016-1-6 · New bearings for the existing Spindle are available locally for a little over 125. They had the quill, for 250, for quite a few years but it's sold now. My machine was used for boring small hydraulic equipment parts on a rotary table nearly it's entire life. The original 2 hp J head …

    Get Price
  • Bridgeport J and 2J Head Pattern Milling Machine ...

    Find many great new & used options and get the best deals for Bridgeport J and 2J Head Pattern Milling Machine Attachment Uses 1/4' Tool Bits at the best online prices …

    Get Price
  • 178 Indicol 1-7/8' Diameter 'C' Frame (Bridgeport 'J'

    The checking of the perpendicularity of the spindle centerline relative to the surface of the table. Bridgeport 'J' Head Size 1-7/8' Quill Extension. Designed to be a universal supporting means for dial test indicators. Built to attach to tools with a head size up to 1-7/8”. …

    Get Price
  • Spindle speed sensor for a Bridgeport 2J head -

    2020-10-6 · Spindle speed sensor for a Bridgeport 2J head was created by rogerfries Strictly speaking my machine is a BOSS 5 CNC machine which uses a variant of the 2J head. Any good place to put a gear tooth sensor or something?

    Get Price
  • Bridgeport Milling Machine Parts Australia |

    2018-9-20 · Bridgeport Mill J Head How To Change Timing Belt You Milling Machine Parts Nt30 Spindle Bearings Assembly For Bridgeport Milling Machine 369178 For Tips For Ing Your First Milling Machine Hackaday Milling Machine Spindle Parts Processing Cnc Vertical Milling Machine 86mm Spindle When Is Manual Machining Better Than Cnc Cnccookbook Be A ...

    Get Price
  • Bridgeport Milling Machine Parts Diagrams Series IJ

    2008-6-7 · All part numbers and images were scanned from a Bridgeport Operators Manual. ** In the works is a Bridgeport repair and troubleshooting page, with how to's and other handy nice to have information. ** My BP 1J Mill (on dealers floor)138kb. Milling Head Front View 1J 67kb. Milling Head Side View 1J 58kb. Power Feed (Original BP Type) 58kb

    Get Price
  • (fif39 SH!:;LBY STREET INDIANAPOLIS. INDIANA

    2012-4-24 · The J head is equipped with a switch to reverse spindle rotation. Model 2J This 2 hp (1.5kW), variable speed milling, drilling and boring head is now more powerful than ever. Among its outstanding features are: infinitely variable speeds from 60 to 4200 rpm; power down-feed and up-feed; counter-balanced quill and spindle; angular positioning ...

    Get Price
  • Bridgeport Parts

    Thank you for choosing H&W to be your supplier of parts for your Bridgeport Milling Machine. Whether it be for the base, head or motor, we carry a large inventory of parts for your mill. If you cannot find the part you are looking for give us a call at 800-285-5271 and one of our helpful staff personal will help you find exactly the part you ...

    Get Price
  • Milling Machine Spindle - The Trout Underground

    This is a BIG Rambaudi milling spindle head with 50 taper and long shaft that is being sold for parts The spindle spins smoothly and freely without any play but the bearings sound dry to me If you don't see it in these pictures it is not included with this auction. except the side cover inclosing the feed gear mechanisms shown in pics 6& 8 IS ...

    Get Price
  • An investigation of the use of heat pipes for machine

    1994-10-1 · Under transient conditions, the energy absorbed by the milling machine head and spindle is related to the energy generated in the spindle bearings and the energy transferred to the surroundings in accordance with the relation- ship: 1040 R.L. JUDD et al. mcdT(t) dt - q - ftA[T(t) - T~o].

    Get Price
  • Bridgeport J and 2J Head Pattern Milling Machine ...

    Find many great new & used options and get the best deals for Bridgeport J and 2J Head Pattern Milling Machine Attachment Uses 1/4' Tool Bits at the best online prices …

    Get Price
  • 178 Indicol 1-7/8' Diameter 'C' Frame (Bridgeport 'J'

    The checking of the perpendicularity of the spindle centerline relative to the surface of the table. Bridgeport 'J' Head Size 1-7/8' Quill Extension. Designed to be a universal supporting means for dial test indicators. Built to attach to tools with a head size up to 1-7/8”. …

    Get Price
  • bridgeport mill | eBay

    BRIDGEPORT Mill Part Milling Machine R8 Spindle Bearings Assembly Taiwan Milling. Brand New. C 90.34. ... Bridgeport J and 2J Head Pattern Milling Machine Attachment Uses 1/4' Tool Bits. Pre-Owned. C 250.98. Top Rated Seller Top Rated Seller. Buy It Now. From United States. S p o n s o r e d.

    Get Price
  • Bridgeport Boss 5 Spindle Oiling and Head Identification

    2014-7-11 · All, I'm in the process of replacing the spindle bearings in my mill and I'm really confused about the lubrication of the spindle bearings. On my mill there is an oiling system that pumps oil to the 'z' axis ball screw, the ways and all of the other ball screws as well from a main reservoir. From what I've read,the spindle bearings require a different lubricant than the ways but by the mills ...

    Get Price
  • Bridgeport Mill Rebuild - NEMES

    2009-6-27 · Latest CD Contents as of 14 Jan 2003 Bridgeport Manuals 1981 Programming Manual 1983 Programming Manual R2E3 Manual Series II NC Programming Manual Student Manual Bridgeport Series 1 Install, Operate and Maintain Manual Quick Change Tooling for the J Head Brown and Sharpe No. 3 Mill Manual Fundamentals of Machine Tools Grinding and Lapping 1907 ...

    Get Price
  • Bridgeport Spindle Bearing Nut Torque - The Home

    2015-11-15 · The inner spacers were so particular they had marks on them to meet the marks of the bearing. By this way, there were fine bearings acting as angular contact bearings because there was a precise preload at the spindle, requiring the balls be drawn up into even finer location of the races. The torque upon the spindle nut was conservative and locked.

    Get Price
  • If Not A Bridgeport....... | ECJ5

    2016-7-3 · I'm actually have a Bridgeport J head for sale, but these things weigh around 2300 lbs, so transportation is a big factor. The old round ram models were prior to around 1956, so there are lots of newer models available that ride on ways/gibs. They are much more stable. The smaller M head Bridgeport uses the less common B&S collets.

    Get Price
  • Building the Bridgeports | American Machinist

    2000-10-31 · Many of Bridgeport's process improvements over the last year or so have focused on its knee-mill production. Bridgeport's first production step is spraying a 0.030-in.-thick filler on the knee mill's major cast iron components — the column, knee, ram, turret, and J housing for the head — to smooth out surface imperfections.

    Get Price
  • Tips For Buying Your First Milling Machine | Hackaday

    2016-8-17 · Bridgeport produced the Series II mill, better than the J in every possible way, but like the Super Beetle, it didn’t stick around long, and like VW, Bridgeport went back to making the antique ...

    Get Price
  • Grease for vertical mill quil bearings? - The Home

    2013-8-28 · about lubing the bearings and the preload on them. They also said a good quality #2 bearing grease (like wheel bearing grease) was fine. They said if the bearings were getting too hot, to reduce the preload on the bearings. In my case, the preload was 5 lbs. in. rolling torque in the spindle bearings of my Millrite. Good Luck!-Blue Chips-Webb

    Get Price
  • bridgeport mill | eBay

    BRIDGEPORT Mill Part Milling Machine R8 Spindle Bearings Assembly Taiwan Milling. Brand New. C 90.34. ... Bridgeport J and 2J Head Pattern Milling Machine Attachment Uses 1/4' Tool Bits. Pre-Owned. C 250.98. Top Rated Seller Top Rated Seller. Buy It Now. From United States. S p o n s o r e d.

    Get Price
  • Bridgeport Spindle Bearing Nut Torque - The Home

    2015-11-15 · The inner spacers were so particular they had marks on them to meet the marks of the bearing. By this way, there were fine bearings acting as angular contact bearings because there was a precise preload at the spindle, requiring the balls be drawn up into even finer location of the races. The torque upon the spindle nut was conservative and locked.

    Get Price
  • Building the Bridgeports | American Machinist

    2000-10-31 · Many of Bridgeport's process improvements over the last year or so have focused on its knee-mill production. Bridgeport's first production step is spraying a 0.030-in.-thick filler on the knee mill's major cast iron components — the column, knee, ram, turret, and J housing for the head — to smooth out surface imperfections.

    Get Price
  • Bridgeport parts quill assembly

    2021-5-8 · Bridgeport quill assembly parts available in new and used, Spares available as single parts or as built assemblies with options new and reconditioned. Bridgeport parts quill assembly …

    Get Price
  • If Not A Bridgeport....... | ECJ5

    2016-7-3 · I'm actually have a Bridgeport J head for sale, but these things weigh around 2300 lbs, so transportation is a big factor. The old round ram models were prior to around 1956, so there are lots of newer models available that ride on ways/gibs. They are much more stable. The smaller M head Bridgeport uses the less common B&S collets.

    Get Price
  • Conversion of my Bridgeport mill to CNC - Pico Systems

    2009-1-17 · Here is a view of the front of the Bridgeport J head, with the Z axis drive mounted to the front. The little red Sumtak encoder can be seen at the top, direct driven from the .1' pitch leadscrew. The block it is mounted to is made in two pieces, with some internal areas opened up to make room for sprockets and mini cog belts for the tach.

    Get Price
  • bridgeport tooling | United States (US)

    Image Size: Sort: Best Match Ending Newest Most Bids Tweet

    Get Price
  • New Grizzly or Used Bridgeport Mill? | BladeForums.com

    2008-7-21 · I did buy a 12' Enco lathe new, having had a bad experience with a used Southbend before. The new lathe had hardened and ground ways, spindle bearings rather than babbit (which was part of the problem on the old SB) and was shiny and new. That was years ago. A clapped out old Bridgeport I had at that time is still running strong.

    Get Price
  • Ekstrom Carlson | Spindle Repair | Dynamic Balancing

    5 spindle drill head: O397: 5 spindle drill head: O397: 6000rpm spindle: 6000rpm spindle motor: A01-7312: 6800 Watt, 9 HP HSD: 96-03-0695: 89-HC-300, 1303-0005-0000: Aggregate head: n/a: Aggregate head – Dual ER32 output: Aggregate head – Dual ER32 output: Warranty: Aggregate head – Dual output: Aggregate head – Dual output: Aggregate ...

    Get Price
  • Grease for vertical mill quil bearings? - The Home

    2013-8-28 · about lubing the bearings and the preload on them. They also said a good quality #2 bearing grease (like wheel bearing grease) was fine. They said if the bearings were getting too hot, to reduce the preload on the bearings. In my case, the preload was 5 lbs. in. rolling torque in the spindle bearings of my Millrite. Good Luck!-Blue Chips-Webb

    Get Price
  • bridgeport_j1_head_2_0_01 Rebuild-10.pdf | Belt ...

    2019-10-10 · The lower spindle bearings inside of the Bridgeport J-Head Quill are precision matched taper bearings with a pre-defined and set preload. What this means is that you have to buy the bearings as a matched set, and if purchased this way, the preload of the bearings is already set if you follow a simple guideline.

    Get Price
  • Round Rod Milling Machine Seting Bearing

    2019-11-29 · Bridgeport J Head Step Pulley Disassembly And Reassembly. Unscrew the spindle top nut after bending down the locking tab Note the bearing separator hanging on the end of the spindle to be used on the press The bearings are a light press fit and they come off …

    Get Price
  • bridgeport milling machine parts list - Induzin

    bridgeport millingmachines machinetool archive. The classic Bridgeport Series 1- a 1966 'Model 9BRJ' and 'Model 12BRJ' - so called because they were fitted with a table either 9 or 12 inches wide and a 1-H.P Model J Head (the Series 1 was listed for the UK market with tables lengths of 32, 36, 42 and 48 inches with, respectively, 20, 24, 30, and 36 inches of longitudinal travel; all the tables ...

    Get Price
  • Bridgeport Series1 Spec Sheet | Bearing (Mechanical ...

    2018-8-19 · Bridgeport Series1 Spec Sheet - Free download as PDF File (.pdf), Text File (.txt) or read online for free.

    Get Price
  • If Not A Bridgeport....... | ECJ5

    2016-7-3 · I'm actually have a Bridgeport J head for sale, but these things weigh around 2300 lbs, so transportation is a big factor. The old round ram models were prior to around 1956, so there are lots of newer models available that ride on ways/gibs. They are much more stable. The smaller M head Bridgeport uses the less common B&S collets.

    Get Price
  • 138 Indicol | Dial Indicator Clamp | Indicator Holder ...

    The 138 Indicol, made for Bridgeport Js, is the perfect way to guarantee that your tool is going to do what you need it to. Designed to be a universal dial indicator clamp. The 138 Indicol indicator holder is the perfect accessory to maintain productivity, save time, and reduce waste.

    Get Price
  • Machine Tool Spindles Selection Guide: Types,

    2021-5-12 · Machine tool spindles are rotating components that are used to hold and drive cutting tools or workpieces on lathes, milling machines and other machine tools. They use belt, gear, motorized, hydraulic or pneumatic drives and are available in a variety of configurations. For example, cartridge ...

    Get Price
  • New Grizzly or Used Bridgeport Mill? | BladeForums.com

    2008-7-21 · I did buy a 12' Enco lathe new, having had a bad experience with a used Southbend before. The new lathe had hardened and ground ways, spindle bearings rather than babbit (which was part of the problem on the old SB) and was shiny and new. That was years ago. A clapped out old Bridgeport I had at that time is still running strong.

    Get Price
  • Milling (machining) - 3D CAD Models & 2D Drawings

    Ram-type mill This can refer to any mill that has a cutting head mounted on a sliding ram. The spindle can be oriented either vertically or horizontally. In practice most mills with rams also involve swiveling ability, whether or not it is called 'turret' mounting. The Bridgeport configuration can be classified as a vertical-head ram-type mill.

    Get Price
  • How Did Pocket NC Survive And Thrive? | Hackaday

    2016-6-1 · The new spindle has way more clamping force on the tool because it uses the ER11 collet system and the tool holders have a solid grab as well. I think they went to this system because it …

    Get Price